En-tete ASCII arduino
Révision datée du 27 juillet 2024 à 09:07 par Antonydbzh (discussion | contributions) (→Exemple : le petit Bot)
Dans les programmes arduino il est parfois utile d'avoir le schéma de brochage
Voici de quoi intégrer au code des schéma.
Sommaire
Exemple : le petit Bot
////////////////////////////////
// Programme //
// Petit Bot //
// Les petits débrouillards //
////////////////////////////////
/*
_________________
/ D1 mini \
|[ ]RST TX[ ]|
|[ ]A0 -GPIO RX[ ]|
|[ ]D0-16 5-D1[X]|----\
|[ ]D5-14 4-D2[X]|--\ \
|[ ]D6-12 0-D3[ ]| | |
|[ ]D7-13 2-D4[ ]| | |
|[ ]D8-15 GND[X]| | |
|[ ]3V3 5V[ ]| | |
_ | +---+ | | |
| | |_______|USB|_______| | / _
| | _ / / _ | |
| | _| |_________ _____/ / _________| |_ | |
| | | ______ |_data D1______________/ |_data D2_| ______ | | |
| | __| | SG90 | |_______________GND_______________________| | SG90 | |___ | |
| |_| |Servo | |_______________Vin_______________________| |Servo | |_| |
| |_| |Gauche| | | |Droit | |_| |
| | |__ |______| | | |______| ___| | |
| | |__ ________| |_________ __| | |
| | |_| |_| | |
| | | |
|_| |_|
Matériel :
- des fils dupont.
- deux servomoteurs à rotation continue
- un D1 mini
- une batterie (C'est quoi une "terie" ? demanda Robin, interloqué, à Batman.).
___
/ ___ \
|_| | |
/_/
_ ___ _
|_| |___|_| |_
___|_ _|
|___| |_|
Les petits Débrouillards 2024 - CC-By-Sa http://creativecommons.org/licenses/by-nc-sa/3.0/
*/
Présentations du programme
////////////////////////////////////
// En-tête Type //
// Code Arduino/Wemos/ESP32 //
// Les petits débrouillards //
// Mis à jour le 27 juil. 2024 //
////////////////////////////////////
/*
Ce programme blablabli...blablabla
*/
Caractère utiles pour fabriquer des trucs
/*
‾
□
○
Ω
*/
Composants électroniques
/*
photorésistance
-(w)-
résistance
-W-
Condensateur
_____
|| |
||1000|
|| µF |
||____|
| |
- +
LED
__
/ \
| |
|______|
|_______|
| |
| |
|
+ -
*/
Micro-controlleurs
/*
Arduino
+-----+
+----[PWR]-------------------| USB |--+
| +-----+ |
| GND/RST2 [ ][ ] |
| MOSI2/SCK2 [ ][ ] A5/SCL[ ] |
| 5V/MISO2 [ ][ ] A4/SDA[ ] |
| AREF[ ] |
| GND[ ] |
| [ ]N/C SCK/13[ ] |
| [ ]IOREF MISO/12[ ] |
| [ ]RST MOSI/11[ ]~|
| [ ]3V3 +---+ 10[ ]~|
| [ ]5v -| A |- 9[ ]~|
| [ ]GND -| R |- 8[ ] |
| [ ]GND -| D |- |
| [ ]Vin -| U |- 7[ ] |
| -| I |- 6[ ]~|
| [ ]A0 -| N |- 5[ ]~|
| [ ]A1 -| O |- 4[ ] |
| [ ]A2 +---+ INT1/3[ ]~|
| [ ]A3 INT0/2[ ] |
| [ ]A4/SDA RST SCK MISO TX>1[ ] |
| [ ]A5/SCL [ ] [ ] [ ] RX<0[ ] |
| [ ] [ ] [ ] |
| UNO_R3 GND MOSI 5V ____________/
\_______________________/
Arduino Pro-micro (Peut émuler un clavier comme Léonardo).
_________________
| Pro micro |
| ATmega32U4 |
|[ ]10-A10 A9-9[ ]|
|[ ]16-MOSI A8-8[ ]|
|[ ]14-MISO 7[ ]|
|[ ]15-SCLK A7-6[ ]|
|[ ]18-A0 5[ ]|
|[ ]19-A1 A6-4[ ]|
|[ ]20-A2 SCL-3[ ]|
|[ ]21-A3 SDA-2[ ]|
|[ ]VCC GND[ ]|
|[ ]RST GND[ ]|
|[ ]GND RX-1[ ]|
|[ ]RAW TX-0[ ]|
| +---+ |
|_______|USB|______|
Arduino NANO
+-----+
+----------| USB |----------+
| +-----+ |
| [ ]D13/SCK MISO/D12[ ] |
| [ ]3.3V MOSI/D11[ ]~|
| [ ]V.ref _ SS/D10[ ]~|
| [ ]A0 / N \ D9[ ]~|
| [ ]A1 / A \ D8[ ] |
| [ ]A2 \ N / D7[ ] |
| [ ]A3 \ 0 / D6[ ]~|
| [ ]A4/SDA D5[ ]~|
| [ ]A5/SCL D4[ ] |
| [ ]A6 INT1/D3[ ]~|
| [ ]A7 INT0/D2[ ] |
| [ ]5V GND[ ] |
| [ ]RST RST[ ] |
| [ ]GND 5V MOSI GND TX1[ ] |
| [ ]Vin [ ] [ ] [ ] RX1[ ] |
| [ ] [ ] [ ] |
| MISO SCK RST |
| NANO-V3 |
+---------------------------+
ESP32 à 36 broches
_______________________
|() ESP32-devKitV1 ()|
| WIFI-BLUETOOTH |
| 36 broches |
|[ ]EN 23-D23[ ]|-SPI MOSI
input only-|[ ]VP-36 22-D22[ ]|-I2C SCL
input only-|[ ]VN-39 1-TXo[ ]|
input only-|[ ]D34-34 3-RXo[ ]|
input only-|[ ]D35-35 21-D21[ ]|-I2C SDA
Touch9-|[ ]D32-32 19-D19[ ]|-SPI MISO
Touch8-|[ ]D33-33 18-D18[ ]|-SPI CLK
DAC1-|[ ]D25-25 5-D5[ ]|-SPI CS0
DAC2-|[ ]D26-26 17-TX2[ ]|
Touch7-|[ ]D27-27 16-RX2[ ]|
Touch6-|[ ]D14-14 4-D4[ ]|-Touch0
Touch5-|[ ]D12-12 2-D2[ ]|-Touch2-LED_BUILTIN
Touch4-|[ ]D13-13 15-D15[ ]|-Touch3
-|[ ]D9-9 0-D0[ ]|-Touch1
-|[ ]D10-10 8-D8[ ]|-
-|[ ]D11-11 7-D7[ ]|-
|[ ]GND 6-D6[ ]|
|[ ]VIN 3V3[ ]| /!\ uniquement sortie
| EN Boot |
|() [o] +---+ [o] ()|
|_________|USB|_________|
ESP32 à 30 broches
_______________________
|() ESP32-devKit V1 ()|
| WIFI-BLUETOOTH |
| 30 broches |
|[ ]EN 23-D23[ ]|-SPI MOSI
input only-|[ ]VP-36 22-D22[ ]|-I2C SCL
input only-|[ ]VN-39 1-TXo[ ]|
input only-|[ ]D34-34 3-RXo[ ]|
input only-|[ ]D35-35 21-D21[ ]|-I2C SDA
Touch9-|[ ]D32-32 19-D19[ ]|-SPI MISO
Touch8-|[ ]D33-33 18-D18[ ]|-SPI CLK
DAC1-|[ ]D25-25 5-D5[ ]|-SPI CS0
DAC2-|[ ]D26-26 17-TX2[ ]|
Touch7-|[ ]D27-27 16-RX2[ ]|
Touch6-|[ ]D14-14 4-D4[ ]|-Touch0
Touch5-|[ ]D12-12 2-D2[ ]|-Touch2-LED_BUILTIN
Touch4-|[ ]D13-13 15-D15[ ]|-Touch3
|[ ]GND GND[ ]|
|[ ]VIN 3V3[ ]| /!\ uniquement sortie
| EN Boot |
|() [o] +---+ [o] ()|
|_________|USB|_________|
Le même
_______________________
|() ESP32-devKitV1 ()|
| WIFI-BLUETOOTH |
| 30 broches |
|[ ]EN 23-D23[ ]|-SPI MOSI
input only-|[ ]VP-36 22-D22[ ]|-I2C SCL
input only-|[ ]VN-39 1-TXo[ ]|
input only-|[ ]D34-34 3-RXo[ ]|
input only-|[ ]D35-35 21-D21[ ]|-I2C SDA
Touch9-|[ ]D32-32 19-D19[ ]|-SPI MISO
Touch8-|[ ]D33-33 18-D18[ ]|-SPI CLK
DAC1-|[ ]D25-25 5-D5[ ]|-SPI CS0
DAC2-|[ ]D26-26 17-TX2[ ]|
Touch7-|[ ]D27-27 16-RX2[ ]|
Touch6-|[ ]D14-14 4-D4[ ]|-Touch0
Touch5-|[ ]D12-12 2-D2[ ]|-Touch2-LED_BUILTIN
Touch4-|[ ]D13-13 15-D15[ ]|-Touch3
|[ ]GND GND[ ]|
|[ ]VIN 3V3[ ]| /!\ uniquement sortie
| EN Boot |
|() [o] +---+ [o] ()|
|_________|USB|_________|
Lolin (Wemos) D1 mini
_________________
/ D1 mini \
|[ ]RST TX[ ]|
|[ ]A0 -GPIO RX[ ]|
|[ ]D0-16 5-D1[ ]| SCL
|[ ]D5-14 4-D2[ ]| SDA
|[ ]D6-12 0-D3[ ]|
|[ ]D7-13 2-D4[ ]| LED_BUILTIN
|[ ]D8-15 GND[ ]|
|[ ]3V3 . 5V[ ]|
| +---+ |
|_______|USB|_______|
_______________
| droit | gauche|
|-------|-------|
| RST | TX |
| A0 | RX |
| D0 16 | D1 5 |
| D5 14 | D2 4 |
| D6 12 | D3 0 |
| D7 13 | D4 2 |
| D8 15 | GND |
| 3V3 | 5V |
|-------|-------|
*/
capteurs
/*
Capteur Capacitif TTP223
dos
+------------+
|[ ]GND |
|[ ]I/O □ |
|[ ]VCC |
|____________|
face
+-------------+
|[ ]VCC /‾‾‾‾\|
|[ ]I/O| |
|[ ]GND \____/|
|_____________|
Bouton poussoir
|___|
| |
| ( ) |
|_____|
| |
Bouton d'arcade
______
/________\
|------|
|------|
|------|
|______|
| |
Gros bouton d'arcade lumineux
_________________
/ \
/ () \
/_______________________\
|------|
|------|
|------|
|------|- LED+
|______|- LED-
| |
Capteur de temérature DHT22
___
/_____\
|_|_|_|_|
|_DHT22_|
|_|_|_|_|
|_|_|_|_|
|_|_|_|_|
| | | |
Capteur de pression Température BME280
______________
|() BME280 |
| VCC [ ]|
| _ GND [ ]|
| |_| SCL [ ]|
| SDA [ ]|
| CSB [ ]|
| SDO [ ]|
|()____________|
Capteur de distance à Ultrasons - HC-SR04
_________________________
| ___ (__) ___ |
| // \\ HC-SR04 // \\ |
||( )| |( )||
| \\___// \\___// |
| VCC TRIG ECHO GND |
|------[ ][ ][ ][ ]-------|
Lecteur RFID_RC522
_____________________________________
| () |
| ()R _-_ |
| F / _-_ \ 3V3[ ]|
| I / / _ \ \ RST[ ]|
| D / / \ \ _ GND[ ]|
| - o |_| IRQ[ ]|
| R \ \ _ / / MISO[ ]|
| C \ \_ _ _/ / MOSI[ ]|
| 5 \ _ _ / SCK[ ]|
| 2 - SDA[ ]|
| ()2 ___ |
|____________________________()_|___|_|
Capteur de CO2 Senseair S8
________________________
| |° ° ° ° ° °| | |
G+ |[ ]| ° ° ° ° °/ |[ ]| DVCC_out
G0 |[ ]|° ° ° ° °/ |[ ]| UART_RxD
Alarm_OC |[ ]|_°_°_°_°| |[ ]| UART_TxD
PWM 1Khz |[ ]| |[ ]| UART_R/T
| | SenseAir® S8 |[ ]| bCAL_in/CAL
|___|________________|___|
Gyroscope et accéléromètre GY-521 - MPU6050
_________________
| MPU6050 ()|
|[ ]VCC |
|[ ]GND G |
|[ ]SCL ___ Y |
|[ ]SDA | | | |
|[ ]XCA |___| 5 |
|[ ]XCL 2 |
|[ ]ADO Y 1 |
|[ ]INT ->X | |
|_______________()|
Capteur de couleur GY-31
___________________________
| () [ ][ ][ ][ ][ ] () |
| INT LED S0 S1 VCC |
| GY-31 |
| _ - _ |
| ( ) / \ ( ) |
| / _ \ |
| ( |_| ) |
| \ / |
| ( ) \_ _ _/ ( ) |
| |
| GND OUT S2 S3 VCC |
| () [ ][ ][ ][ ][ ] () |
---------------------------
Capteur capacitif MPR121
_________________
| L 11[ ]|
| E 10[ ]|
| D 9[ ]|
3,3V-|[X]3,3V / 8[ ]|
|[ ]IRQ e 7[ ]|
A5-|[X]SCL l 6[ ]|
A4-|[X]SDA e 5[ ]|
|[ ]ADD c 4[ ]|
GND-|[X]GND t 3[ ]|
| r 2[ ]|
| o 1[ ]|
| MPR121 d 0[ ]|
|_________e_______|
Encodeur rotatif
A = broche A de l'encodeur
B = broche B de l'encodeur
G = GND
SW = bouton poussoir de l'encodeur
A G B
_|_|_|_
| _ |
| / \ |
| \ _ / |
|_______|
| |
G SW
Horloge
______________________________
| POWER //////// |
-|[ ]32k | RTC | |
-|[ ]SQW |DS3231 | SCL[ ]|
-|[ ]SCL | | SDA[ ]|
-|[ ]SDA \\\\\\\\ VCC[ ]|
-|[ ]VCC ___ GND[ ]|
-|[ ]GND |___| |
|______________________________|
Lecteur de carte SD
______________________________
| SD CARD _____________|
-|[ ]GND MODULE | /
-|[ ]3,3V [XXX] | / |
-|[ ]5 = | / |
-|[ ]CS = | | |
-|[ ]MOSI = | | |
-|[ ]SCK . = | \ |
-|[ ]MISO = | \ |
-|[ ]GND = |_________\___
|______________________________|
*/
Actionneurs
/*
Ecran OLED
GND 5V D5 D6
______|_|_|_|______
|() * * * * ()|
| GND VCC SCL SDA |
| _______________ |
| | | |
| | | |
| | | |
| |_______________| |
|()_______________()|
Servomoteur
___
|_°_|
| |
| ^ |
| | | |
| (o) |
| |
|_____|
|_°_|
|||
|| \___ data
| \____ Vin
\_____ GND
___
|_°_|
| ^ |
| | | |
| | | |
| (o) |
|Servo|
|_____|
|_°_|
|||
|| \___ data
| \____ Vin
\_____ GND
___
|_°_|
| / |
| / /
| / /|
| (o) |
|Servo|
|_____|
|_°_|
|||
|| \___ data
| \____ Vin
\_____ GND
___
|_°_|
| |
| |
| __|___
| (o)_____/
|Servo|
|_____|
|_°_|
|||
|| \___ data
| \____ Vin
\_____ GND
_
_________| |_
| ______ |
| | | |___
| |Servo | |_
| | | |_|
| |______| ___|
|_________ __|
||| |_|
|| \___ data
| \____ Vin
\_____ GND
Matrice de LED 8X8 :
________________
In | O O O O O O O O | Out
-> | O O O O O O O O | ->
VCC [ ]| O O O O O O O O |[ ] VCC
GND [ ]| O O O O O O O O |[ ] GND
DIn [ ]| O O O O O O O O |[ ] DOut
CS [ ]| O O O O O O O O |[ ] CS
CLK [ ]| O O O O O O O O |[ ] CLK
| O O O O O O O O |
-----------------
Lecteur MP3
+-------\_/--------+
+5V |[X] MP3-TF-16P [ ]|
resistance 1K - RX |[X] DFPlayer [ ]|
TX |[X] __________ [ ]|
|[ ]| |[ ]|
|[ ]| CARTE |[ ]|
Haut-Parleur |[X]| SD |[ ]|
GND |[X]| |[ ]|
Haut-Parleur |[X]| |[ ]|
|___|__________|___|
Haut-Parleur
/|
/ |
_ / |
-| | |
-|_| |
\ |
\ |
\|
|\
| \
| \ _
| | |-
| |_|-
| /
| /
|/
Ampli son : MAX98357A
______________________
|() |o o| ()|
| -|____|+ |
| = = ____ = = |
| MAX | | " " |
| 98357A |____| = |
|I2C Amp |
|LRC DIN SD VIN|
|[ ][ ][ ][ ] [ ][ ][ ]|
|__BCLK__GAIN____GND___|
Ruban de LED WS2812B - néopixel
_________________________ ____________
GND ->|= __ = __ = / / __ = |-> GND
Din ->|= |__| '' = |__| '' = \ \ |__| '' = |-> Dout
+5V ->|=__________=__________=_/ /________ =__|-> +5V
*/
Autres infos
/*
Matériel :
- des fils dupont.
- une breadbord
- Arduino
- ...
Schéma de l'Arduino en ASCII-ART CC-By http://busyducks.com/ascii-art-arduinos
Sous licence CC-By-Sa (http://creativecommons.org/licenses/by-nc-sa/3.0/)
*/
/*
___
/ ___ \
|_| | |
/_/
_ ___ _
|_| |___|_| |_
___|_ _|
|___| |_|
Les petits Débrouillards 2024 - CC-By-Sa http://creativecommons.org/licenses/by-nc-sa/3.0/
*/
