ENIB 2023 : Les 7 erreurs

Photo de l'équipe

Que fait ce projet ?

C'est un escape game centrée sur la langue des signes. Il faut se repérer à travers le puzzle de manière à trouver le mot caché. Du code cachée, à des séquences cachées il faut manœuvrer de manière subtile. Les leds sont de bons conseils.

Liste des composants

• Leds
• écran LCD
• interrupteur
• carte arduino
• cables
• images

Avancé du projet

Pour décrypter les lettres du code, le joueur devra comprendre des lettres en langues des signes (Un documentation est donné mais par forcément l'ordre ... )

Décor

Afin de placer un décor dans le style, nous avons créer sur inkskate nos propres images. Grâce à la découpe laser, nous avons pu le mettre sur une planche de bois. Les dessins n'ont pas été choisis par hasard, ils ont un rapport avec le mot à trouver.

Ici se trouve le fichier pour la réserve de carte

Ici se trouve le fichier du ring de box

Code

/*


                                     D1 mini
                                     BROCHAGE
                                _________________
                               /     D1 mini     \
                              |[ ]RST        TX[ ]|
                              |[ ]A0  -GPIO  RX[ ]|
                              |[ ]D0-16    5-D1[ ]| SCL
                              |[ ]D5-14    4-D2[ ]| SDA
                              |[ ]D6-12    0-D3[ ]|
                              |[ ]D7-13    2-D4[ ]| LED_BUILTIN
                              |[ ]D8-15     GND[ ]|
                              |[ ]3V3 .      5V[ ]|
                              |       +---+       |
                              |_______|USB|_______|

  _______________

  2 fois jaune

  */



int green=0;
int yellow=4;
int orange=2;



void setup() {
  Serial.begin(9600); 
  
  pinMode(green, OUTPUT);
  pinMode(yellow, OUTPUT);
  pinMode(orange, OUTPUT);


}

void loop() {
                                     //code qui allume les leds dans l'ordre des cartes
    digitalWrite(yellow, HIGH);  
    delay(500);
    digitalWrite(yellow, LOW); 
    delay(500);
    digitalWrite(yellow, HIGH);  
    delay(500);
    digitalWrite(yellow, LOW); 
    delay(2000);

    digitalWrite(orange, HIGH);   
    delay(500);
    digitalWrite(orange, LOW);
    delay(2000);

    digitalWrite(yellow, HIGH); 
    delay(500);
    digitalWrite(yellow, LOW); 
    delay(500);
    digitalWrite(yellow, HIGH);  
    delay(500);
    digitalWrite(yellow, LOW); 
    delay(500);
    digitalWrite(yellow, HIGH);
    delay(500);
    digitalWrite(yellow, LOW);    
    delay(2000);

    digitalWrite(green, HIGH); 
    delay(500);
    digitalWrite(green, LOW);
    delay(500); 
    digitalWrite(green, HIGH); 
    delay(500);
    digitalWrite(green, LOW);  
    delay(2000);

    digitalWrite(green, HIGH); 
    delay(500);
    digitalWrite(green, LOW);
    delay(500); 
    digitalWrite(green, HIGH); 
    delay(500);
    digitalWrite(green, LOW);  
    delay(2000);

    digitalWrite(green, HIGH); 
    delay(500);
    digitalWrite(green, LOW); 
    delay(2000);

    digitalWrite(green, HIGH); 
    delay(500);
    digitalWrite(green, LOW);
    delay(500); 
    digitalWrite(green, HIGH); 
    delay(500);
    digitalWrite(green, LOW);
    delay(500); 
    digitalWrite(green, HIGH);
    delay(500);
    digitalWrite(green, LOW);   
    delay(2000);

    digitalWrite(orange, HIGH);   
    delay(500);
    digitalWrite(orange, LOW);
    delay(500); 
    digitalWrite(orange, HIGH);   
    delay(500);
    digitalWrite(orange, LOW);
    delay(500); 
    digitalWrite(orange, HIGH);  
    delay(500);
    digitalWrite(orange, LOW);  
    delay(5000);

}


/*


                                     D1 mini
                                     BROCHAGE
                                _________________
                               /     D1 mini     \
                              |[ ]RST        TX[ ]|
                              |[ ]A0  -GPIO  RX[ ]|
                              |[ ]D0-16    5-D1[ ]| SCL
                              |[ ]D5-14    4-D2[ ]| SDA
                              |[ ]D6-12    0-D3[ ]|
                              |[ ]D7-13    2-D4[ ]| LED_BUILTIN
                              |[ ]D8-15     GND[ ]|
                              |[ ]3V3 .      5V[ ]|
                              |       +---+       |
                              |_______|USB|_______|

  _______________
*/                                                          //code pour la sélection des lettres avec les interrupteurs en binaire 
#include <LiquidCrystal_I2C.h>
#include <string>
int i1=15;
int i2=13;
int i3=12;
int i4=14;
int i5=A0;
int i=0;
int btn=TX;

String w = "STALLONE";
LiquidCrystal_I2C lcd(0x27, 16, 2); 
void setup() {
  // put your setup code here, to run once:
  Serial.begin(9600);
  pinMode(i1, INPUT);
  pinMode(i2, INPUT);
  pinMode(i3, INPUT);
  pinMode(i4, INPUT);
  pinMode(i5, INPUT);

  // initialize LCD
  lcd.init();
  // turn on LCD backlight                      
  lcd.backlight();

}

void loop() {
  // put your main code here, to run repeatedly:
  int etatI1 = digitalRead(i1);
  int etatI2 = digitalRead(i2);
  int etatI3 = digitalRead(i3);
  int etatI4 = digitalRead(i4);
  int etatI5 = digitalRead(i5);
  

if(etatI5==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("A");

}
else if(etatI4==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("B");
}
else if(etatI4==HIGH && etatI5==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("C");
}
else if(etatI3==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("D");
}
else if(etatI3==HIGH && etatI5==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("E");
}
else if(etatI3==HIGH && etatI4==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("F");
}
else if(etatI3==HIGH && etatI4==HIGH && etatI5==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("G");
}
else if(etatI2==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("H");
}
else if(etatI2==HIGH && etatI5==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("I");
}
else if(etatI2==HIGH && etatI4==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("J");
}
else if(etatI2==HIGH && etatI4==HIGH && etatI5==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("K");
}
else if(etatI2==HIGH && etatI3==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("L");
}
else if(etatI2==HIGH && etatI3==HIGH && etatI5==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("M");
}
else if(etatI2==HIGH && etatI3==HIGH && etatI4==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("N");
}
else if(etatI2==HIGH && etatI3==HIGH && etatI4==HIGH && etatI5==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("O");
}
else if(etatI1==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("P");
}
else if(etatI1==HIGH && etatI5==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("Q");
}
else if(etatI1==HIGH && etatI4==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("R");
}
else if(etatI1==HIGH && etatI4==HIGH && etatI5==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("S");
}
else if(etatI1==HIGH && etatI3==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("T");
}
else if(etatI1==HIGH && etatI3==HIGH && etatI5==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("U");
}
else if(etatI1==HIGH && etatI3==HIGH && etatI4==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("V");
}
else if(etatI1==HIGH && etatI3==HIGH && etatI4==HIGH && etatI5==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("W");
}
else if(etatI1==HIGH && etatI2==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("X");
}
else if(etatI1==HIGH && etatI2==HIGH && etatI5==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("Y");
}
else if(etatI1==HIGH && etatI2==HIGH && etatI4==HIGH){
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("Z");
}
else{
  // set cursor to first column, first row
  lcd.setCursor(0, 0);
  // print message
  lcd.print("no");

}

/*
if(digitalRead(btn)==HIGH){
  
  if(lcd.read()==w[i]){
    lcd.setCursor(0, 1);
    lcd.print("ok");
    i+=1;
  }
  else{
    i=0;
  }

  
}*/

}